The percentage error in the calculated volume of a sphere, if there is 2% error in its diameter measurement, is __________.
- A
1
- B
2
- C
6
- D
8
Every JEE Main question on Errors in measurement and significant figures, one of the ideas inside Units, Dimensions & Errors: 75 questions from 2008–2026, 42 of them in the last five years. Newest first, answer key on every one. Free to read.
Questions
75
Years asked
16
Since
2008
Of the chapter
34%
Questions on Errors in measurement and significant figures in each year it was asked, the latest 12 of 16.
1–20 OF 75 · NEWEST FIRST
The percentage error in the calculated volume of a sphere, if there is 2% error in its diameter measurement, is __________.
1
2
6
8
The density of a uniform cylinder is determined by measuring its mass , length and diameter . The measured values of , and are 97.42 0.02 g, 8.35 0.05 mm and 20.20 0.02 mm, respectively. Calculated percentage fractional error in is _______.
0.63%
0.82%
0.72%
0.25%
The diameter of a wire measured by a screw gauge of least count 0.001 cm is 0.08 cm. The length measured by a scale of least count 0.1 cm is 150 cm. When a weight of 100 N is applied to the wire, the extension in length is 0.5 cm, measured by a micrometer of least count 0.001 cm. The error in the measured Young's modulus is N/m. The value of is __________ . (Ignore the contribution of the load to Young's modulus error calculation)
In an experiment to determine the resistance of a given wire using Ohm’s law, the voltmeter and ammeter readings are noted as and , respectively. The least counts of voltmeter and ammeter are and , respectively. The estimated error in the resistance measurement is_______Ω.
To compare EMF of two cells using potentiometer the balancing lengths obtained are 200 cm and 150 cm. The least count of scale is 1 cm. The percentage error in the ratio of EMFs is______
1.55
1.75
1.65
1.17
Keeping tl1e significant figures in view, the sum of the physical quantities 52.01 m, 153.2 m and 0.123 m is:
205m
205.333m
205.33 m
205.3m
The speed of a longitudinal wave in a metallic bar is 400 m/s. If the density and Young's modulus of the bar material are increased by 0.5% and 1 %, respectively then the speed of the wave is changed approximately to m/ s.
402
399
401
398
The time period of a simple harmonic oscillator is . Measured value of mass (m) of the object is 10 g with an accuracy of 10 mg and time for 50 oscillations of the spring is found to be 60 s using a watch of 2 s resolution. Percentage error in determination of spring constant (k) is________%.
3.35
3.43
7.60
6.76
Four persons measure the length of a rod as 20.00 cm, 19.75 cm, 17.01 cm and 18.25cm. The relative error in the measurement of average length of the rod is :
0.24
0.18
0.08
0.06
In an experiment the values of two spring constants were measured as . lf these springs are connected in parallel, then the percentage error in equivalent spring constant is :
1.67%
1.33%
2.33%
2.67%
A spherical body of radius r and density falls freely through a viscous liquid having density and viscosity and attains a terminal velocity . Estimated maximum error in the quantity is: (Ignore errors associated with and g, gravitational acceleration)
A quantity Q is formulated as . X, Y and Z are independent parameters which have fractional errors of 0.1, 0.2 and 0.5, respectively in measurement. The maximum fractional error of Q is
0.1
0.8
0.7
0.6
A person measures mass of 3 different particles as 435.42 g, 226.3 g and 0.125 g. According to the rules for arithmetic operations with significant figures, the additions of the masses of 3 particles will be.
g
g
g
g
The maximum percentage error in the measurment of density of a wire is [Given, mass of wire radius of wire length of wire ]
8
5
4
7
The energy of a system is given as , where t is the time and . The errors in the measurement of and t are 1.2% and 1.6%, respectively. At t=5s,maximum percentage error in the energy is:
6%
8.4%
11.6%
4$
For an experimental expression where all the digits are significant. Then to report the value of we should write
A physical quantity Q is related to four observables a,b,c,d as follows : where, ; ; ; and , then the percentage error in Q is , where x = ________ .
A physical quantity C is related to four other quantities p, q, r and s as follows: . The percentage errors in the measurement of p, q, r and s are 1%, 2%, 3% and 2% respectively. The percentage error in the measurement of C will be ________ %.
In an experiment to measure focal length (f) of convex lens, the least counts of the measuring scales for the position of object (u) and for the position of image (v) are and , respectively. The error in the measurement of the focal length of the convex lens will be:
The radius , length and resistance of a metal wire was measured in the laboratory as cm, ohm, cm. The percentage error in resistivity of the material of the wire is :