The Vernier constant of Vernier callipers is 0.1 mm and it has zero error of (0.05 cm). While measuring diameter of a sphere, the main scale reading is 1.7 cm and coinciding vernier division is 5. The corrected diameter will be ______ cm.
Every JEE Main question on Vernier calipers: least count and zero error, one of the ideas inside Experimental Skills: 31 questions from 2009–2026, 22 of them in the last five years. Newest first, answer key on every one. Free to read.
Questions
31
Years asked
11
Since
2009
Of the chapter
52%
21–31 OF 31 · NEWEST FIRST
The Vernier constant of Vernier callipers is 0.1 mm and it has zero error of (0.05 cm). While measuring diameter of a sphere, the main scale reading is 1.7 cm and coinciding vernier division is 5. The corrected diameter will be ______ cm.
The one division of main scale of Vernier callipers reads and divisions of Vernier scale is equal to the divisions on main scale. When the two jaws of the instrument touch each other the zero of the Vernier lies to the right of zero of the main scale and its fourth division coincides with a main scale division. When a spherical bob is tightly placed between the two jaws, the zero of the Vernier scale lies in between and and Vernier division coincides with a main scale division. The diameter of the bob will be ______ .
One main scale division of a vernier callipers is cm and division of the vernier scale coincide with division of the main scale. The least count of the callipers in mm is:
The vernier scale used for measurement has a positive zero error of 0.2 mm. If while taking a measurement it was noted that 0 on the vernier scale lies between 8.5 cm and 8.6 cm. Vernier coincidence is 6, then the correct value of measurement is cm. (least count = 0.01 cm)
8.36 cm
8.54 cm
8.58 cm
8.56 cm
The diameter of a spherical bob is measured using a vernier callipers. 9 divisions of the main scale, in the vernier callipers, are equal to 10 divisions of vernier scale. One main scale division is 1 mm. The main scale reading is 10 mm and 8th division of vernier scale was found to coincide exactly with one of the main scale division. If the given vernier callipers has positive zero error of 0.04 cm, then the radius of the bob is _________ cm.
The least count of the main scale of a vernier calipers is 1 mm. Its vernier scale is divided into 10 divisions and coincide with 9 divisions of the main scale. When jaws are touching each other, the 7 division of the vernier scale coincides with a division of the main scale and the zero of vernier scale is lying right side of the zero of the main scale. When this vernier is used to measure the length of the cylinder the zero of the vernier scale between 3.1 cm and 3.2 cm and 4 VSD coincides with the main scale division. The length of the cylinder is (VSD is vernier scale division):
3.2 cm
3.21 cm
3.07 cm
2.99 cm
Diameter of a steel ball is measured using a Vernier calipers which has divisions of 0.1 cm on its main scale (MS) and 10 divisions of its Vernier scale (VS) match 9 divisions on the main scale. Three such measurements for a ball are given as:
S.No. MS (cm) VS divisions
1. 0.5 8
2. 0.5 4
3. 0.5 6
If the zero error is -0.03 cm, then mean corrected diameter is:
0.53 cm
0.56 cm
0.59 cm
0.52 cm
A student measured the length of a rod and wrote it as 3.50 cm. Which instrument did he use to measure it?
A meter scale
A vernier calliper where the 10 divisions in vernier scale matches with 9 divisions in main scale and main scale has 10 divisions in 1 cm
A screw gauge having 100 divisions in the circular scale and pitch as 1 mm
A screw gauge having 50 divisions in the circular scale and pitch as 1 mm
A spectrometer gives the following reading when used to measure the angle of a prism. Main scale reading: degree; Vernier scale reading: divisions. Given that division on main scale corresponds to degree. Total divisions on the vernier scale are and match with divisions of the main scale. The angle of the prism from the above data
divisions on the main scale of a vernier calliper coincide with divisions of the vernier scale. If each division of main scale is units, then the least count of the instrument is
In an experiment the angles are required to be measured using an instrument. divisions of the main scale exactly coincide with the divisions of the vernier scale. If the smallest division of the main scale is half-a-degree , then the least count of the instrument is
one minute
half minute
one degree
half degree
RELATED EXPERIMENTAL SKILLS TOPICS