A rod of length 5L is bent right angle keeping one side length as 2L.
The position of the centre of mass of the system: (Consider L = 10 cm)
- A
- B
- C
- D
Every JEE Main question on Centre of mass of continuous bodies and cavities, one of the ideas inside Centre of Mass, Momentum & Collisions: 21 questions from 2005–2025, 8 of them in the last five years. Newest first, answer key on every one. Free to read.
Questions
21
Years asked
12
Since
2005
Of the chapter
16%
Questions on Centre of mass of continuous bodies and cavities in each year it was asked.
1–20 OF 21 · NEWEST FIRST
A rod of length 5L is bent right angle keeping one side length as 2L.
The position of the centre of mass of the system: (Consider L = 10 cm)
Consider a circular disc of radius 20 cm with centre located at the origin. A circular hole of radius 5 cm is cut from this disc in such a way that the edge of the hole touches the edge of the disc. The distance of centre of mass of residual or remaining disc from the origin will be
2.0 cm
1.5 cm
1.0 cm
0.5 cm
The center of mass of a thin rectangular plate (fig - x) with sides of length a and b, whose mass per unit area varies as (where is a constant), would be

A uniform thin metal plate of mass with dimensions is shown in the figure below. The ratio of and coordinates of center of mass of the plate is . The value of is ________.

The distance of centre of mass from end A of a one dimensional rod (AB) having mass density kg m and length (in meter) is m. The value of is _____ (where is the distance from end A)
A circular hole of radius is cut out of a circular disc of radius as shown in figure. The centroid of the remaining circular portion with respect to point O will be:

The disc of mass with uniform surface mass density is shown in the figure. The center of mass of the quarter disc (the shaded area) is at the position where is ________. (Round off to the Nearest Integer) [ is an area as shown in the figure]

The position of the centre of mass of a uniform semi-circular wire of radius placed in plane with its centre at the origin and the line joining its ends as -axis is given by . Then, the value of is ___.
The coordinates of the centre of mass of a uniform flag-shaped lamina (thin flat plate) of mass 4 kg. (The coordinates of the same are shown in the figure) are:

(1.25 m, 1.50 m)
(0.75 m, 1.75 m)
(0.75 m, 0.75 m)
(1 m, 1.75 m)
A rod of length has non-uniform linear mass density given by , where and are constants and . The value of for the centre of mass of the rod is at:
As shown in figure. When a spherical cavity (centred at O) of radius 1 is cut out of a uniform sphere of radius R (centred at C), the centre of mass of remaining (shaded part of sphere is at G, i.e., on the surface of the cavity. R can be determined by the equation:

A square shaped hole of side is carved out at a distance from the centre 'O' of a uniform circular disk of radius a. If the distance of the centre of mass of the remaining portion from O is , value of X (to the nearest integer) is:

The centre of mass of a solid hemisphere of radius is from the centre of the flat surface. Then value of is___
A uniform rectangular thin sheet of mass has length and breadth , as shown in the figure. If the shaded portion is cut-off, the coordinates of the centre of mass of the remaining portion will be:

In the figure shown is a uniform wire. If the center of mass of the wire lies vertically below point , then is close to

1.85
1.5
1.37
3
Distance of the centre of mass of a solid uniform cone from its vertex is . If the radius of its base is and its height is then is equal to
A uniform thin rod AB of length has linear mass density , where is measured from A. If the CM of the rod lies at a distance of from A, then and are related as:
A thin bar of length L has a mass per unit length , that increases linearly with distance from one end. If its total mass is M and its mass per unit length at the lighter end is , then the distance of the centre of mass from the lighter end is:
A thin rod of length '' is lying along the -axis with its ends at and . Its linear density (mass/length) varies with as , where can be zero or any positive number. If the position of the centre of mass of the rod is plotted against '', which of the following graphs best approximates the dependence of on ?




A circular disc of radius is removed from a bigger circular disc of radius such that the circumferences of the discs coincide. The centre of mass of the new disc is from the centre of the bigger disc. The value of is
RELATED CENTRE OF MASS, MOMENTUM & COLLISIONS TOPICS