The force required to stretch a wire of cross-section 1 cm to double its length will be: (Given Young's modulus of the wire N m)
- A
N
- B
N
- C
N
- D
N
Every Mechanical Properties of Solids question JEE Main has set, grouped by the idea it tests rather than the order of the syllabus. 126 questions across 6 distinct ideas. Free to read, answer key on every one.
Questions
126
Distinct ideas
6
Share of marks
3.4%
Difficulty
EASY
A chapter is not one subject — it is a handful of procedures the examiner reuses. These are the ones Mechanical Properties of Solids questions actually test.
61–80 OF 126 · NEWEST FIRST
The force required to stretch a wire of cross-section 1 cm to double its length will be: (Given Young's modulus of the wire N m)
N
N
N
N
The bulk modulus of a liquid is Nm. The pressure required to reduce the volume of liquid by is :
N m
N m
N m
N m
A steel wire of length 3.2 m and a copper wire of length 4.4 m , both of radius 1.4 mm are connected end to end. When stretched by a load, the net elongation is found to be 1.4 mm. The load applied, in Newton, will be: (Given )
360
180
1080
154
If the length of a wire is made double and radius is halved of its respective values. Then, the Young's modulus of the material of the wire will:
Remain same
Become 8 times its initial value
Become of its initial value
Become 4 times its initial value
A wire of length is hanging from a fixed support. The length changes to and when masses 1 kg and 2 kg are suspended respectively from its free end. Then the value of is equal to
A metal wire of length 0.5 m and cross-sectional area m has breaking stress N m. A block of 10 kg is attached at one end of the string and is rotating in a horizontal circle. The maximum linear velocity of block will be _____ m s
The elongation of a wire on the surface of the earth is m. The same wire of same dimensions is elongated by m on another planet. The acceleration due to gravity on the planet will be ______ m s. (Take acceleration due to gravity on the surface of earth m s)
A wire of length and radius is clamped rigidly at one end. When the other end of the wire is pulled by a force , its length increases by . Another wire of the same material of length and radius is pulled by a force under same conditions. The increase in length of this wire is ______ cm.
A uniform heavy rod of mass , cross sectional area and length is hanging from a fixed support. Neglecting the lateral contraction, the elongation in the rod due to its own weight is . The value of is ______. (Given: Young's modulus and )
A square aluminium (shear modulus is ) slab of side and thickness is subjected to a shearing force (on its narrow face) of . The lower edge is riveted to the floor. The displacement of the upper edge is ______ .
In an experiment to determine the Young's modulus, steel wires of five different lengths (1, 2, 3, 4 and 5 m) but of same cross-section area were taken and the curves between extension and load were obtained. The slope (extension/load) of the curves were plotted with the wire length and the following graph was obtained. If the Young's modulus of the given steel wire is , then the value of is _____

The elastic behaviour of material for linear stress and linear strain, is shown in the figure. The energy density for a linear strain of is ______ kJ m. Assume that material is elastic upto the linear strain of .

A string of area of cross-section 4 mm and length 0.5 is connected with a rigid body of mass 2 kg. The body is rotated in a vertical circular path of radius 0.5 m. The body acquires a speed of 5 m s at the bottom of the circular path. Strain produced in the string when the body is at the bottom of the circle is _____ . (Use Young's modulus N m and )
The speed of a transverse wave passing through a string of length 50 cm and mass 10 g is 60 m s. The area of cross-section of the wire is 2.0 mm and its Young's modulus is N m. The extension of the wire over its natural length due to its tension will be m. The value of x is _____
The value of tension in a long thin metal wire has been changed from to . The lengths of the metal wire at two different values of tension and are and , respectively. The actual length of the metal wire is:
An object is located at 2 km beneath the surface of the water. If the fractional compression is 1.36%, the ratio of hydraulic stress to the corresponding hydraulic strain will be ________. [Given: density of water is 1000 kg m and m s].
N m
N m
N m
N m
Two wires of same length and radius are joined end to end and loaded. The Young's moduli of the materials of the two wires are and . The combination behaves as a single wire then its Young's modulus is:
If , and are the values of Young's modulus, bulk modulus and modulus of rigidity of any material respectively. Choose the correct relation for these parameters.
N m
N m
N m
N m
Given below are two statements: one is labelled as Assertion A and the other is labelled as Reason R.
Assertion A: When a rod lying freely is heated, no thermal stress is developed in it.
Reason R: On heating, the length of the rod increases.
In the light of the above statements, choose the correct answer from the options given below:
Both A and R are true and R is the correct explanation of A
A is false but R is true
Both A and R are true but R is NOT the correct explanation of A
A is true but R is false
A uniform heavy rod of weight 10 kg m s, cross-sectional area 100 cm and length 20 cm is hanging from a fixed support. Young modulus of the material of the rod is N m. Neglecting the lateral contraction, find the elongation of rod due to its own weight:
m
m
m
m
OTHER PHYSICS CHAPTERS