RankRizz
JEE MAIN 2021 · 18 MAR S2+4 / −1HARDTRANSCRIBED

JEE Main 2021 Physics question — Torque and the rotational form of Newton's second law

A solid cylinder of mass mm is wrapped with an inextensible light string and, is placed on a rough inclined plane as shown in the figure. The frictional force acting between the cylinder and the inclined plane is:

Figure for JEE Main 2021 Physics question on Torque and the rotational form of Newton's second law


[The coefficient of static friction, μs\mu_s, is 0.4]

SOLUTION

We need to determine the frictional force acting between a solid cylinder of mass mm and a rough inclined plane when a light string is wrapped around it as shown in the figure.

1. Identify the System Configuration and Parameters

From the diagram and text, we have:

  • Mass of the solid cylinder = mm
  • Angle of inclination (θ\theta) = 60∘60^\circ
  • Coefficient of static friction (μs\mu_s) = 0.40.4
  • A light, inextensible string is wrapped around the cylinder, with one end anchored firmly to the wall at the top of the incline. The string runs parallel to the inclined plane.

2. Analyze the Equations of Equilibrium

Let's check if the cylinder can remain in a state of static equilibrium under the action of gravity, string tension (TT), normal force (NN), and static friction (ff):

  1. Force Balance Perpendicular to the Incline:

    N=mgcos⁡60∘=12mgN = mg \cos 60^\circ = \frac{1}{2}mg

  2. Force Balance Parallel to the Incline:
    The component of gravity pulling the cylinder down the slope is mgsin⁡60∘mg \sin 60^\circ. Both the tension TT from the upper string segment and the static frictional force ff act upwards along the incline to oppose this downward pull:

    T+f=mgsin⁡60∘— (Equation 1)T + f = mg \sin 60^\circ \quad \text{--- (Equation 1)}

  3. Torque Balance about the Center of Mass (CM):
    Taking the center of the cylinder as our rotation axis, gravity and the normal force pass directly through the center and create no torque. The tension TT acts at the top boundary with a radius RR tending to rotate it counter-clockwise, while friction ff acts at the bottom contact point with a radius RR tending to rotate it clockwise:

    τnet=T⋅R−f⋅R=0\tau_{\text{net}} = T \cdot R - f \cdot R = 0

    T⋅R=f⋅R  ⟹  T=f— (Equation 2)T \cdot R = f \cdot R \implies T = f \quad \text{--- (Equation 2)}

3. Calculate the Required Frictional Force (ff)

Substitute T=fT = f from Equation 2 into Equation 1:

f+f=mgsin⁡60∘f + f = mg \sin 60^\circ

2f=mg(32)2f = mg \left(\frac{\sqrt{3}}{2}\right)

f=34mg≈0.433 mgf = \frac{\sqrt{3}}{4}mg \approx 0.433\, mg

4. Verify the Static Friction Limit

For this equilibrium configuration to physically hold true without slipping, the required frictional force cannot exceed the maximum available limiting static friction (fmaxf_{\text{max}}):

fmax=μsN=0.4×(12mg)=0.2 mgf_{\text{max}} = \mu_s N = 0.4 \times \left(\frac{1}{2}mg\right) = 0.2\, mg

Comparing the values:

frequired≈0.433 mg>fmax=0.2 mgf_{\text{required}} \approx 0.433\, mg > f_{\text{max}} = 0.2\, mg

Since the required friction to keep the cylinder static is significantly larger than the maximum possible friction the surface can supply, static equilibrium cannot be maintained. The cylinder will slip and roll down the incline, meaning the string becomes slack (T=0T = 0).

When the string goes slack, the cylinder undergoes standard pure rolling down a rough incline, where the dynamic rolling friction is given by:

f=mgsin⁡θ1+mR2If = \frac{mg \sin\theta}{1 + \frac{mR^2}{I}}

For a solid cylinder, I=12mR2  ⟹  mR2I=2I = \frac{1}{2}mR^2 \implies \frac{mR^2}{I} = 2. Thus:

f=mgsin⁡60∘1+2=13⋅mg⋅32=36mg≈0.288 mgf = \frac{mg \sin 60^\circ}{1 + 2} = \frac{1}{3} \cdot mg \cdot \frac{\sqrt{3}}{2} = \frac{\sqrt{3}}{6}mg \approx 0.288\, mg

Since this kinetic/rolling value also overshoots the maximum boundaries of the rough surface (0.2 mg0.2\,mg), the system transitions fully into a pure kinetic sliding state governed entirely by its maximum friction limit:

f=μkN=μsN=0.2 mg=15mgf = \mu_k N = \mu_s N = 0.2\, mg = \frac{1}{5}mg

Conclusion

The frictional force acting between the cylinder and the inclined plane settles at its maximum limit of mg5\frac{mg}{5}, which corresponds to Option C.

Tagged Torque and the rotational form of Newton's second law. Machine-assigned, so read it as a strong shortlist rather than a verdict.

SubjectPhysics
TopicTorque and the rotational form of Newton's second law
TypeMultiple choice